duram duramax
 
 
textured coatings waterproofing antislip

Product Data Sheet

Maxitex

Bold, High Build, Acrylic Texture Coating With A Stipple Texture Finish

Description

Duramax MAXITEX is a high performance, high solids, high build acrylic decorative texture coating in a matt finish. Depending how it is applied it provides a high or low stipple finish in a wide range of colours. It is recommended that MAXITEX be top coated with SUPREME or MAXIFLEX decorative and protective membrane coatings.

Uses

MAXITEX may be applied on primed internal and external walls. Due to its high build most substrate imperfections can be hidden or obscured.The surface must be primed with MAXIPRIME prior to the application of the MAXITEX.

Suitable Surfaces

Suitable for application on sound, primed off - form concrete, cement render, FC sheeting, Harditex sheeting (or similar), other concrete products and brick surfaces. Substrates and or joints may need to be prepared or skimmed with MAXIJOINT, MAXICRETE or MAXIPATCH .

Specification

The information contained in this product data sheet is typical but does not constitute a full specification as conditions and specific requirements may vary from project to project. The instructions should be considered as a minimum requirement but the applicator or contractor must use their skill, knowledge and experience to carry out additional works as may be necessary to meet the requirements of the project. Specification for specific projects should be sought from the Company in writing.

Limitations

Do not apply if rain or frost is imminent or possible before the product has properly dried. The product should not be subjected to hydrostatic pressure and excessive rising damp. Ambient temperature: Min. 10oC Max. 35oC Surface temperature: Min. 5oC Max. 50oC

Benefits and Advantages

Ease of application & maintenance.
Excellent adhesion.
Excellent weathering & abrasion resistance.
Dirt resistance.
Allows surface to breathe.
Application safety, water based, non combustible.
High tensile strength.

Precautions in Use

The product is safe to use if used properly. The use of gloves, goggles and coveralls is recommended while applying MAXITEX.

Priming and Surface Preparation

Good preparation is essential. Surfaces must be sound, stable, dry, clean and free of dust, loose, flaking, friable material and substances that may diminish adhesion.

 

Prime surface with MAXIPRIME. At a rate of 6 to 8 sq.m per litre.  Allow to dry for approximately 4 hours before application of MAXITEX.
Cracks must be filled with suitable filler and finished flush accordance with good painting practice. A penetrating sealer may be required.

Application

Apply MAXITEX  using a texture roller. Application  should be in 1 direction to achieve a uniform pattern.
Ambient temperature: Min. 10oC  Max. 35oC
Surface temperature: Min. 5oC  Max. 45oC
Do not apply if rain or frost is imminent or possible before the product has cured.
Thoroughly mix product before application. (Power stirrer).

Application Experience
We recommend that the product is applied by person with the appropriate skills and experience for the type of product. The acceptability of the surface is the responsibility of the applicator.

Coverage

The stated average coverage rate may vary depending upon type, condition, porosity, texture of the surface and application technique.

 

The following approximate average spread rate for MAXITEX is: 25 to 30 sq. m. per 15 litre pail but dependant on the information above. Allow +/- 50% increase in usage for high build textures. MAXIPRIME: Undiluted: 6 to 8 sq.m. per litre usually applied in 1 coat. Diluted: +/- 14 sq. m. per litre after the addition of 30% clean water.

Colours

Available in a wide range of colours.

 

Colour Batches
Whilst care is taken to accurately colour match, batch to batch variations may occur for reasons which may be beyond our control. We strongly advise that project requirements are ordered in a single batch lot to avoid colour matching from batch to batch. Minimum quantities and tinting charges may apply.

 

Contractor Responsibility
It is the responsibility of the contractor or applicator to ensure that the colour is within specification prior to its application. The Company shall not be liable for any colour variations after the product has been applied. Further, the applicator should use product for touch-ups from the same batches used to do the original coats.

Drying and Curing

Drying and curing of the product is affected by type, dryness and porosity of the surface, temperature, humidity, ventilation, climate conditions and application technique and therefore drying and curing can only be given as a guide.

 

Touch Dry: 2 to 4 hours at 20oC. Recoat: 6 hours. Full cure: 2 to 3 days.

Storage

Available in 15 Lt Pails. Store in a cool, dry area, away from extreme elements. Shelf life: 6 to 12 months in unopened containers. Containers should be rotated to prevent settlement.

Clean Up

Wet spills can be cleaned with water. Ensure product does not enter drains.

Safety & Precautions

The use of gloves, goggles and coveralls is recommended as the product may irritate skin and eyes. If swallowed give water to drink and seek medical assistance. If in eyes, flush thoroughly with clean water, holding lid open to ensure any trapped product maybe flushed away. If on skin, remove contaminated clothing and wash with soap and water. Do not use solvents. If inhaled, unlikely due to viscosity of product, remove person to fresh air and apply artifical respiration if required.

 

For full safety data refer to the products Material Safety Data Sheet. Observe precautions as per label.

Issued: 1 May 2012 | Valid to: 31 May 2020

Conditions of Use and Disclaimer

The information contained in this Material Data Sheet is given in good faith based upon our current knowledge and does not imply warranty, express or implied. The information is provided and the product is sold on the basis that the product is used for its intended purpose and is used in a proper workmanlike manner in accordance with the instructions of the Product Data Sheet in suitable and safe working conditions. Under no circumstances will the Company be liable for loss, consequential or otherwise, arising from the use of the product.

 

DURAM PTY LTD ABN 50 612 836 718
The Ultimate in Waterproofing & Protective Coating Technology

Duram Offices:
NEW SOUTH WALES: 51 Prince William Drive, Seven Hills, NSW 2147

 Tel (02) 9624 4077  Fax: (02) 9624 4079

QUEENSLAND: Unit 4, 29 Collinsvale St Rocklea, QLD 4106

Tel (07) 3255 6478  Fax: (07) 3255 6258